Vonnic Standalone DVR Manual de usuario

VONNIC Standalone DVR Quick Start Guide Version 6.0.3

6 2 Overview of Navigation and Controls Before operation, please make sure:  You have properly installed HDD and all the cable connections. 

7 Figure 2-2 2.1.2 Main Menu After you logged in, the system main menu is shown as below. See Figure 2-3. There are total six icons: search, i

8 Please note, before you replace the HDD, do remember shutting down the device and unplug the power cable. 2.1.4 Auto Resume after Power Failure

9 1 Realtime playback It is to playback the previous 5-60 minutes record of current channel. Please go to the Main Menu->General t

10  Schedule: Channel records as you have set in recording setup (Main Menu->Setting->Schedule)  Stop: All channels stop recording. Figu

11 Figure 2-9  All channel manual record Please highlight “ALL” after “Manual.” See Figure 2-10. When system is in manual recording, all schedule

12 2.4 Search & Playback Click search button in the main menu, search interface is shown as below. See Figure 2-12. Usually there are three fil

13 and channel selection pane.  In 4-window playback mode: you can select 4 channels according to your requirement.  In 9-window playback mode

14 ► Slow play In playback mode, click it to realize various slow play modes such as slow play 1, slow play 2, and etc.  Fast forward In playbac

15 can see the slide bar restore its previous position.  Click Backup button after clip, you can save current contents in a new file.  You can

i Table of Contents 1 Hardware Installation and Connection... 1 1.1 Check Unpa

16 Figure 2-13 Click the , you can go to the smart search playback. Click it again, system stops smart search playback. Important  System does

17 Figure 2-14 2.4.3 Mark Playback Please make sure your purchased device support this function. You can use this function only if you can see t

18 Usually, system can playback previous N seconds record if there is such a kind of record file. Otherwise, system playbacks from the previous X se

19  Storage: This function is null right now.  Frame rate: PAL：1-25fps.NTSC:30fps.  Bit stream value: Default setup is 1024Kb/S. Figure 2-17

20 Please highlight icon to select the corresponding function. After completing all the setups please click save button, system goes back to the p

21 Please note, if you select ALL in Figure 2-20, the record setup of all channels are the same and the Copy button becomes hidden. Figure 2-20 2.

22 Playback or search in the redundant disk. There are two ways for you to playback or search in the redundant disk.  Set redundant disk(s) as rea

23  In Encode interface, click snapshot button to input snapshot mode, size, quality and frequency. See the interface on the left of Figure 2-23.

24 Figure 2-24 2.7 Network Here is for you to input network information. The single network adapter interface is shown as in Figure 2-25 and the

25 network service. System may pop up dialog box for you to confirm setup when you want to change MTU setup. Click OK button to confirm current rebo

ii 2.6.2 Activation Snapshot... 22 2.6.3 Priority...

26 Figure 2-25 Figure 2-26 2.7.1 Network Setting Network setting interface is shown as in Figure 2-27. Please check the box to enable correspond

27 2.8 Pan/Tilt/Zoom Please note:  Slight difference may be found in the user’s interface, due to various protocols.  Please make sure the spee

28 Here you can set the following items:  Step: value ranges from 1 to 8.  Zoom  Focus  Iris Click icon and to adjust zoom, focus and

29 3 Web Operation Slightly difference may be found in the interface due to different series. 3.1 Network Connection Before web client operation,

30 3.3 Main Window 3.3.1 LAN Login For the LAN mode, after you logged in, you can see the main window. See Figure 3-2. Click the channel name on

31 Figure 3-3 For detailed operation information, please refer to the User’s Manual included in the resources CD.

32 Appendix Toxic or Hazardous Materials or Elements Component Name Toxic or Hazardous Materials or Elements Pb Hg Cd Cr VI PBB PBDE Sheet Metal(Ca

iii Welcome Thank you for purchasing our DVR! This quick start guide will help you become familiar with our DVR in a very short time. Before install

1 1 Hardware Installation and Connection Note: All the installation and operations here should conform to your local electric safety rules. 1.1 Ch

2 1.5 Front Panel The front panel is shown as in Figure 1-1. Figure 1-1 Please refer to the followin

3 When playback, click it to restore real-time monitor mode. Enter ENTER Confirm current operation Go to default button Go to menu Assistant Fn On

4 Please refer to the following sheet for detailed information. 1 Video input 2 Video output 3 Audio output 4 Audio input 5 Video VGA output 6 H

5 3 Audio output 4 Audio input 5 Video VGA output 6 HDMI port 7 USB port 8 Network port 9 RS-485 port 10 Power socket 11 On/off button